ENGLISH 简体中文 日本語 한국어  


애플리케이션 노트  998

5V Step-Down Converter Has Transformer-Isolated Feedback

The circuit of Figure 1 shows an alternative to opto-isolated feedback signals (the system shown is a 5V switching regulator). The zero (non-existent) line regulation of a push/pull, surface-mount transformer and driver (T2 and IC2) produces an isolated feedback signal (to pin 3 of IC1) proportional to the regulator's nominal 5V output. The result is a fully isolated dc-dc converter without the usual opto-isolator bandwidth constraints and aging characteristics.

Figure 1. This fully isolated 5V switching regulator offers long-term reliability and ease of design.
Figure 1. This fully isolated 5V switching regulator offers long-term reliability and ease of design.

By alternately grounding each end of T2's center-tapped primary, the transformer driver (IC2) generates an ac signal proportional to the desired 5V feedback voltage. A diode bridge (CR2–R5) and capacitor (C4) convert this transformer's output to dc, and a diode-resistor network (CR1, R3, R4) compensates for the diode bridge's temperature coefficient. (You can substitute silicon signal diodes, such as 1N4148s, for the Schottky diodes.) The result is a zero-TC voltage slightly less than ½VOUT. Transformer T1 isolates VOUT.

In response to a 5V output, the feedback network produces an isolated 2.404V (at IC1, pin 3) and introduces about 250ns of delay at 100kHz—the equivalent of 9° of phase shift. This bandwidth is sufficient for the control loop in most switching converters. Supply current for IC2 and the temperature compensation network together is about 6mA.

Starting with a 5V, nonisolated transformer flyback converter in which VOUT connects directly to the top of C1 and R1, you can insert the isolated-feedback circuit (bottom of Figure 1) between VOUT and C1/R1. To accommodate this extra isolated-feedback circuit, simply reduce the value of R1 to ensure that the R1/R2 divider voltage is comparable to IC1's internal feedback reference (1.5V).

The isolated converter's performance is virtually identical to that of the nonisolated converter, except for isolated-feedback-circuit power consumption. T2 provides 500VRMS isolation. (You can also get transformers with 1500VRMS isolation.)


의견을 보내주세요!
위 내용이 도움이 되셨나요?
여러분의 의견을 기다립니다 — Maxim은 보내주신 정정이나 제안사항을 반영하고 있습니다. 이 페이지를 평가하고 의견을 보내주십시오.


자동 업데이트
관심있는 분야의 애플리케이션 노트가 나올 때 자동으로 업데이트 받고 싶으세요? 그렇다면 EE-Mail™을 신청하십시오.



추가 정보  APP 998: Jul 09, 1998
MAX770 5V/12V/15V 또는 가변출력, 고효율 Low-IQ, 스텝 업 DC-DC 컨트롤러 전체 데이터 시트
(PDF, 216kB)
무료 샘플
MAX845 PCMCIA 애플리케이션용 절연 변압기 드라이버 전체 데이터 시트
(PDF, 224kB)
 

다운로드, PDF 형식다운로드, PDF 형식 (24kB)
 AN998, AN 998, APP998, Appnote998, Appnote 998


      개인정보보호 정책    법적 고지

      Copyright © 2008 by Maxim Integrated Products, Dallas Semiconductor