Calculating Maximum Operating Frequency for Delay Lines
Abstract: Delay lines are used in applications that require a signal delay of a few nanoseconds (ns) or where incremental timing corrections are needed for the system to work properly. This application note discusses the maximum frequency that the input signal could have, and the maximum delay that can be obtained.
When calculating the maximum input frequency, the critical parameter to consider is the minimum pulse width of the input signal. For periodic signals with a 50% duty cycle, the minimum pulse width would be half the period of the signal. This value, in turn, determines the maximum possible delay. Sometimes the input is periodic with a low frequency, but with a duty cycle of less than 50%. In this case, the width of the minimum duration between transitions (tWI) on the input determines the minimum pulse width (Figure 1). In a number of devices, the minimum-input pulse width possible is specified as 100% of the maximum output delay desired (if not explicitly specified). The maximum output delay for these devices is, therefore (conversely), the same as the minimum-input pulse width.
Figure 1. Illustration shows how the minimum duration between transitions (tWI) of the input signal determines the maximum possible delay.
Maximum Input Frequency for Programmable Delay Lines
The specifications to consider for programmable delay lines are found in the product data sheet:
Zero-step delay (tPHL_MIN or tPLH_MIN)
Minimum-input pulse width (tWI_MIN)
The minimum-input pulse width is usually specified explicitly in the data sheet, but is sometimes specified relative to the output delay desired. Therefore, to calculate the minimum-input pulse width, we consider the minimum delay that can be programmed, which is the same as the zero-step delay. The data sheet also specifies an error or tolerance over temperature and voltage. This error is added to the zero-step delay to determine the maximum zero-step delay. The maximum zero-step delay is essentially the minimum pulse width to consider (tWI_MIN). The maximum frequency (fIN_MAX) can then be calculated from the minimum-input pulse width using the following formula:
Table 1 gives some examples of the maximum allowable frequency for various devices.
Table 1. Maximum Input Frequencies for Programmable Delay Lines
Part Number
Description
Minimum or Zero-Step Delay, tPHL_MIN or tPLH_MIN (ns)
Maximum Zero-Step Delay (ns)
Minimum Pulse Width tWI_MIN (ns)
Maximum Input Frequency (MHz)
DS1020-100
8-bit silicon delay line
10 ± 2
12
100% of output delay
12
41.67
DS1020-25
8-bit silicon delay line
10 ± 2
12
100% of output delay
12
41.67
DS1021-25
8-bit silicon delay line
10 ± 2
12
100% of output delay
12
41.67
DS1023-25
8-bit timing element
16.5
22
20
20
25
DS1023-500
8-bit timing element
16.5
22
50
50
10
DS1045-3
4-bit dual delay line
9 ± 1
10
100% of output delay
10
50
Maximum Input Frequency for Nonprogrammable Delay Lines
For nonprogrammable delay lines, the specifications to consider are also found in the product data sheet:
Delay at maximum tap position
Minimum-input pulse width (tWI_MIN)
The minimum-input pulse width is specified relative to the delay at maximum tap position. If an error is specified, it is added to this delay to obtain the maximum delay at the maximum tap position. This value is then used to calculate the minimum pulse width (tWI_MIN). The maximum frequency (fIN_MAX) can then be calculated from the minimum-input pulse width using Equation 1 above.
Table 2 shows some examples of the maximum allowable frequency for various nonprogrammable devices.
Table 2. Maximum Input Frequencies for Nonprogrammable Delay Lines
Part Number
Description
Delay at Maximum Tap Position
Maximum Delay at Max Tap Position
Minimum Pulse Width, tWI_MIN (ns)
Maximum Input Frequency (MHz)
DS1110LE-200
3V, 10-tap silicon delay line
200
200
10% of tap 10 delay
20
25
DS1110LE-500
3V, 10-tap silicon delay line
500
500
10% of tap 10 delay
50
10
DS1135-6
3-in-1 high-speed silicon delay line
6 ± 1
7
100% of tap delay
7
71.43
DS1135-30
3-in-1 high-speed silicon delay line
30 ± 1.5
31.5
100% of tap delay
31.5
15.87
Calculating Maximum Frequency for an Application
For programmable delay lines: if a delay higher than the minimum delay is required, then the minimum pulse width allowable is calculated as:
Minimum Pulse Width = Maximum Step-Zero Delay + Programmed Delay.
The maximum allowable frequency can then be calculated using Equation 1.
다운로드, PDF 형식
